Immersion Heater Switch: Which 20A Switch Do You Need?

The switch for your immersion heater looks like any other white plate on the wall. It is not. An immersion heater switch carries a heavy load for hours, so it needs the right rating and the right poles. This guide covers the choice, using the 20A double pole switch range and BG's own data.

TEO team · Updated 13 November 2026 · England · 8 min read

Quick answerAn immersion heater switch should be a 20A double pole switch. A 3kW element draws about 13A, which is more than a 10A light switch is built for. A dual heater with a sink and bath option adds a selector, and the BG 83112 combines both. Use a registered electrician for any new circuit.

13ACurrent drawn by a 3kW element at 230V
20ARating of the BG 83x double pole switches
30 yearsBG warranty listed for the 83112

Which immersion heater switch does a cylinder need?

A cylinder needs a 20A double pole switch, usually marked water heater. The load is the reason. A 3kW element at 230V draws 3000 divided by 230, which is about 13A, and it keeps drawing it until the thermostat cuts out.

Double pole means the switch breaks both live and neutral. BG lists double pole switching on its 83x range for a safer installation. A plain light switch breaks one conductor and is rated far lower, so it is the wrong part for this job.

RuleNever fit a 6A or 10A light switch to an immersion heater. Use a 20A double pole switch, and follow the heater maker's instructions for the circuit.

Single or dual heater: what the sink and bath switch does

A dual immersion heater has two heating options in one cylinder, and the 83112 has a second switch to choose between them. The BG 83112 has an on and off switch with an LED indicator on the left, and a sink and bath selector on the right.

Layout of the BG 83112 dual immersion heater switch ONOFFSINKBATH20A double pole, LED indicator10A selectorSchematic of the layout BG describes, not to scale.
The 83112 layout as BG describes it. The left rocker has the indicator, and the right rocker selects sink or bath.

BG says to switch to bath with off-peak electricity to heat a full tank cheaply, and to sink to heat a small amount on dearer electricity as a top-up. Which element each position powers depends on how the heater is wired, so follow the heater maker's instructions.

BG 83x codes compared

BG numbers its white moulded 20A double pole switches in the 83x group. The last digits tell you what you get.

Code Switching Indicator Flex outlet Marking
830 20A double pole No No Plain
831 20A double pole LED No Plain
832WH 20A double pole No Yes Water heater
833WH 20A double pole LED Yes Water heater
83112 20A double pole plus 10A sink and bath selector LED Not listed Sink and bath

The BG data lists a 25mm minimum box depth for the 830, 832WH, 833WH and 83112. See BG's own 83112 data page for the full detail.

Fixed cable or flex outlet?

A flex outlet lets a flexible cable leave the switch plate towards the heater. The BG Nexus 20A Water Heater switch with flex outlet comes with a 50mm surface pattress box and was £7.09 and in stock on 13 November 2026. The page lists a 25mm minimum box depth and IP20.

The page does not say whether any flex is included, so buy the cable your heater's instructions call for. Our other TEO guides cover how a flex outlet differs from a brush plate.

What to check before you order

  • Rating: 20A double pole, marked or plain.
  • Selector: a dual heater with sink and bath needs the 83112 or a switch with the same function.
  • Indicator: choose an LED version if you want to see that the heater is on.
  • Cable entry: pick a flex outlet if a flexible cable runs to the heater.
  • Back box: 25mm minimum on the listed BG switches.

If you want a grid switch instead, the BG Nexus Grid white collection lists a 20A double pole module labelled Water Heater at £2.97 and in stock on 13 November 2026. A grid module needs a frame and plate, and it has no sink and bath selector.

If the plate must match white fittings elsewhere in the room, the white switches and sockets collection lists 250 products, 237 in stock on 13 November 2026.

Worked example: six flats, six cylinders

A landlord replaces six failed switches on six single-element cylinders, each a like-for-like swap.

  • Six switches with flex outlet: 6 at £7.09 is £42.54.
  • Six BG 83112 switches instead: 6 at £8.38 is £50.28.
  • Difference: £7.74 across the block, or £1.29 a flat.

The 83112 only makes sense where the heater is a dual unit that uses the sink and bath option. On a single element, a plain or flex outlet switch does the job for less.

Part P: who can fit an immersion heater switch

In England, swapping a switch like for like is not notifiable under Part P, but a new circuit is. Read our Part P guide, and the GOV.UK Approved Document P page, which applies to England only.

Work in a room with a bath or shower needs more care. Isolate at the consumer unit, prove the circuit dead, and bring in a registered electrician if the job grows. Wales, Scotland and Northern Ireland have their own rules.

Where immersion heater switch orders go wrong

  • Buying a light switch. It is not rated for the load.
  • Ordering a plain switch for a dual heater. It has no sink and bath selector.
  • Assuming the 83112 has a flex outlet. BG does not list one.
  • Skipping the back box. Check 25mm before you remove the old plate.

FAQs

It needs a 20A double pole switch, usually marked water heater. A 3kW element draws about 13A, which is more than a light switch should carry. Follow the heater maker's instructions for the circuit, and use a registered electrician for any new circuit.

A double pole switch breaks both live and neutral, and BG lists double pole switching on its 83x range for a safer installation. It also suits the heavy, steady current an element draws. A light switch breaks one conductor and is rated lower.

On a dual immersion heater, BG says to switch to bath with off-peak electricity to heat a full tank cheaply, and to sink to heat a small amount as a top-up. Which element each position powers depends on how the heater is wired, so follow the instructions.

No. A 3kW element draws about 13A at 230V, which exceeds a 10A rating, and a light switch is not meant to carry that load for hours. Use a 20A double pole switch, and check the heater's own instructions before you fit it.

In England, swapping a switch like for like is not notifiable under Part P, but a new circuit is, and work near a bath or shower needs extra care. The work must still be safe, so isolate and prove the circuit dead, or use a registered electrician.

BG lists a 25mm minimum mounting box depth for the 83112. The plate holds two rockers, so check the plate size against your box before you remove the old switch. The 832WH style with flex outlet also lists 25mm, and our listing comes with a 50mm pattress box.

Yes, it has an LED power indicator on the on and off rocker, which BG describes as reliable and low power. The right rocker is the sink and bath selector. The 830 has no indicator, and the 831 has an LED, so choose by whether you want to see the heater is on.

BG lists a 30 year warranty on the 83112 and the 832WH, and the flex outlet switch we stock also lists 30 years. The 83112 is also anti-microbial, according to BG. Warranty terms are BG's, so check them on the BG page before you rely on them.

Choose your 20A double pole switch

See every 20A double pole switch, with live stock.

Shop 20A double pole switches
Related News
Cart
Close
Back
Account
Close